Reactor E-10
Electric foam and polyurea dispenser
Suitable for finishing works and small projects using polyurethane foam and polyurea – it causes up to 5.4 kg (12 lbs) per minute
Reactor E-10 produced by Graco is a small, ready-to-use system that helps you get to know such equipment and do small work without sacrificing performance. Reactor E-10 Sprayers are ideal for multi-component spraying, joint filling and finishing work. Thanks to the rapidly configurable and easy-to-use intelligent controls, the E-10 will become a natural addition to the dosing line.
Features
- he small size is ideal for portability in the work area, as well as for hard-to-reach areas
- Operation by one person saves time and material
- Use as an addition to existing spray equipment
- Versatility – switching between cold spraying, hot spraying and spraying with foam
- Saves 30% of material costs compared to recycled foam systems
Small ready-to-use systems with great results!
- Low power consumption and connection to standard outlets
- Simple start, stop and digital temperature display with one-button operation
- Pressure balancing valves ensure a quick and easy balancing of the system pressure
- Balanced dosing eliminates pressure fluctuations, ensuring even spray
- The easy-to-maintain fluid supply section reduces maintenance time and improves productivity.
- Electric motor improves productivity and reduces operating costs
- Stand-alone transparent liquid tanks show that the spraying is carried out with a predetermined ratio
- The power of the heaters and hose is up to 2000 W for preheating the circulating material
Specifications
| Reactor E-10 | |
| Maximum Fluid Working Pressure |
140 bar, 14 MPa
|
| Maximum Fluid Temperature |
71 ° C
|
| Maximum Ambient Temperature |
43 ° C
|
| Maximum Output at 340 cycles / min |
5.4 kg / min
|
| Output per Cycle (A and B) |
0.0133 liter
|
| Overpressure Relief |
Recirc / Spray valves automatically relieve excessive fluid pressure back to supply tanks
|
| Weight (approximately, depending on model) |
72 kg
|
| Wetted Parts |
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
|
| Electrical Requirements | |
| Model AP9570, CS9570: |
120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits
|
| Model AP9571, CS9571: |
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits
|
| Model AP9572, CS9572: |
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit
|
| Model 249806: |
120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit
|
| Model 249808: |
240 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 8 A circuit
|
| Generator Size (for Reactor E-10 only) | |
| Heated: |
5000 W minimum
|
| Nonheated: |
2500 W minimum
|
| Heater Power | |
| 120V models: |
850 W each; 1700 W total
|
| 240V models: |
1000 W each; 2000 W total
|
| Sounds Pressure | |
| Fast Circulation Mode: |
78.7 dB (A)
|
| At 2000 psi (14 MPa, 140 bar), 0.72 gpm (2.7 lpm): |
84.5 dB (A)
|
| Sound Power, measured per ISO 9416-2 | |
| Fast Circulation Mode: |
88.6 dB (A)
|
| At 2000 psi (14 MPa, 140 bar, 0.72 gpm (2.7 lpm): |
94.4 dB (A)
|
| Tank Capacity (nominal) |
26.5 liters
|
| Fluid Outlets | |
| Component A (ISO): |
-5 JIC male
|
| Component B (RES): |
-6 JIC male
|
| Fluid Circulation Ports | |
| Component A (ISO): |
-5 JIC male
|
| Component B (RES): |
-6 JIC male
|
| Air Inlet |
1/4 in quick-disconnect industrial type pin fitting
|
| Air Outlet |
1/4 npsm (m)
|
| Gun Compressed Air Requirements | |
| Fusion Gun (purge air and operating air): |
0.112 m³ / min
|
| 2K Ultra-Lite Gun with disposable mixer kit, with air spray valve fully open: |
0.392 m³ / min
|
| 2K Ultra-Lite Gun with joint fill kit: |
0.056 m³ / min
|
| Hose Markings | |
| A Side |
Red
|
| B Side |
Blue
|